ESD5111 | GAC Multi-VDC / Standard Unit

SDG Series - Programming Harness for SDG514 & 524 with Serial Port

2.3 in. [58mm] Thread Length / #8-32NC-2A Thread Stud Terminals / High Output 1.2kΩ

ADD (Packard) Actuators - Connector Kit Replacement / 2-Terminal

12VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m] / Lesser Rate Return Spring SP203 / Thin Rubber Stop 26 Degrees Travel

12VDC / Packard Connector without Mating Connector / Perkins 403D-15, 403D-15T & Caterpillar C1.7

MSP Military-Style (Amphenol) Sensors - 10 ft. [3m] Shielded Harness / Straight Connector EC1100 / 2-Terminal

10 Turn / 1KΩ

ACB, ADB, ATB-T4 Military-Style (Amphenol) Actuators - 12 ft. [3.6m] Harness / 90° Connector EC1010 / 6-Terminal

3.45 in. [88mm] Thread Length / 2.25 in. [57mm] Harness / Same as MSP6734 except with Packard Connector without Mating Connector / Aluminum Gold Anodized

12VDC / Light-Force (Low-Current Optimized PID)

12VDC / Packard Connector with Mating Connector EC1300 / Cold Start Solenoid / Install Kit KT291 Included

24VDC / Packard Connector without Mating Connector / Single (ADD) or Double Rack Bearing (ACD) / Bosch Install Kit KT289 (ADD) or BYC ASIMCO KT283 (ACD) Included

2.37 in. [60mm] Thread Length / 6 in. [152mm] Harness / Male Push-On Terminals / Aluminum Gold Anodized

5-Star Torx Bit - Pump Cover Screws (Service Tool)

24VDC / Standard Unit

24VDC / Universal - Caterpillar & Cummins / 4-20mA or 0-5VDC Load Sharing Input / 100% Max Duty Cycle Output

3.13 in. [79mm] Thread Length / 3 in. [76mm] Harness / Automotive Connector / Stainless

12VDC / Packard Connector without Mating Connector / Perkins 404D-15, 404D-22 & Caterpillar C2.2T, C3.4

24VDC / Barber Colman - Dyna 1 & 8000 Speed Control to GAC LSM/SYC / 5kΩ Trim Pot Input / Selectable 50/60Hz Operation

4.3 in. [110mm] - Actuator Control Lever - 1/4 in. [6.35mm] Holes / Serrated Shaft

24VDC / Military-Style Connector without Mating Connector / Position Feedback Sensor (Novotechnik) / Note - Compatible with EEG6500 Series

2.7 in. [69mm] Thread Length / 6 in. [152mm] Harness / Male Push-On Terminals

12VDC / Packard Connector without Mating Connector / Kubota 03 Series V2003, V2203, V2403

24VDC / Drives 2 Identical Actuators Simultaneously (Diesel or Gaseous)

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m] / Greater Rate Return Spring SP207

24VDC / Packard Connector without Mating Connector

3.13 in. [79mm] Thread Length / 3 in. [76mm] Harness / Packard Connector without Mating Connector / Stainless

24VDC / Interface Module Scania S6 (EMS) EFI SY to GAC LSM/SYC / Nominal 5VDC Input / 1.6VDC Output

AFR Series - 8 ft. [2.4m] Harness / Flying Leads / 35-Wires

24VDC / Terminal Strip

Multi-VDC / Built-In Display / Terminal Strip / All Actuators (Including ACB2001) / Built-In Configurable Speed Switch Output / Advanced CAN J1939 support / Battery Voltage, Hour Meters / Variable Speed 0-5VDC or 4-20mA Input

3.86 in. [98mm] Thread Length / 1 ft. [0.3m] Harness / Flying Leads / Aluminum Clear Anodized

ADD/ADE175 Series Installation Kit - Spare for Bosch-Style Pumps (Included with Actuator) - Hardware, Gasket, Shutoff Plate, Spring, Retainer, Linkage / Note - KT289 includes all of KT283

24V / ADC225S with Integrated EDG6000 / Requires EC1502 or CH1520 (Not Included)

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m]

Multi-VDC / Light-Force (Low-Current Optimized PID) / For Cummins EFC Forward Acting (Normally Closed)