KT275 | GAC 175 or 275 Installation Kit - Bosch P 3000 Series Camshaft Bearing Retainer Kit - Plate, Gasket, Seal, Shims, Hardware

176 Series Installation Kit - For Bosch RS/RSV Governor / Left-Hand Rack / Mounts Actuator Directly to Intermediary Mechanical Governor Housing - Adapter Plate, Linkage, Gasket, Hardware

ALN Series - Clevis Kit Only

12VDC / Standard Unit

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m] / Lesser Rate Return Spring SP203

MSP Military-Style (Amphenol) Sensor - Mating Connector Kit / With 90˚ Cable Clamp & Weather Boot / 2-Terminal

24VDC / Packard Connector without Mating Connector / Install Kit KT291 Included

MSP Packard Sensors - Mating Connector Kit / 2-Terminal

24VDC / Male Push-On Terminals / Isuzu L-Series 3LB1, 3LD1, 3LD2, 4LE1, 4LE2

10 Turn / 5kΩ / Multiple Variable Speed Control / Vernier Dial

24VDC / Packard Connector without Mating Connector / Perkins 403D-15, 403D-15T & Caterpillar C1.7

Multi-VDC / Light-Force (Low-Current Optimized PID) / For Cummins EFC Forward Acting (Normally Closed)

3.19 in. [81mm] Thread Length / 6.25 in. [159mm] Harness / Packard Connector / Same as MSP6728 with Mating Connector Kit EC1350 / Stainless

3.16 in. [80mm] Thread Length / 3.25 in. [83mm] Harness / Dual Output / Dual Packard Connectors / Same as MSP6732 with Mating Connector Kit (Qty 2) EC1350 / Stainless

24VDC / Commercial Connector with Mating Harness CH251-2134 7 ft. [2.13m]

M6 I.D. End and Thread

Multi-VDC / Overspeed Switch

MSP Packard Sensors - Connector Kit Replacement / 2-Terminal

EDG6000 - Programming Interface Assembly with Serial Port

EDG6000 Series - 8 ft. [2.4m] Harness / Flying Leads / 14-Wires

24VDC / Cummins EFC Speed Control to GAC LSM/SYC / 5kΩ Trim Pot Input

24VDC / Heinzmann EG or KG6-04/10-04 Speed Control to GAC LSM/SYC

24VDC / Packard Connector without Mating Connector / Includes KT295 Installation Kit

5.0 in. [127mm] Thread Length / #8-32NC-2A Thread Stud Terminals / High Output 1.3kΩ

24VDC / Light-Force (Low-Current Optimized PID)

MSP Packard Sensors - 10 ft. [3m] Shielded Harness / 2-Terminal

24VDC / Packard Connector without Mating Connector

Non-CE / 24VDC / Isochronous Load Sharing / Load Anticipation / Droop / Forward and Reverse Power Monitoring and Reset Capability

ADC (Commercial) Actuators - 7 ft. [2.13m] Harness / 2-Terminal

12VDC / 13.0 lbf. [6.0 kg] / 0.50 ft-lb [0.68 J] Work / Male Push-On Terminals

12VDC / Packard Connector without Mating Connector / Shibaura (Perkins) N843-C, N844L-C, N844LT-C (Caterpillar C-series or Volvo D2, contact GAC)

12VDC / Packard Connector with Mating Connector EC1300 / Cold Start Solenoid / Install Kit KT291 Included

12VDC / Deutsch Connector without Mating Connector / Same as ACD110A

2.7 in. [69mm] Thread Length / 6 ft. [1.8m] Shielded Cable / Flying Leads / Stainless

24VDC / Interface Module Scania S6 (EMS) EFI SY to GAC LSM/SYC / Nominal 5VDC Input / 1.6VDC Output

12VDC / Light-Force (Low-Current Optimized PID)

12VDC / Packard Connector with Mating Connector EC1300 / Includes KT188 Installation Kit